Ansa opzioni binarie falson 900 - inseabrona’s blog

Step-by-Step Guide for Adding a Stack, Expanding Control Lines, and Building an Assembler

After the positive response to my first tutorial on expanding the RAM, I thought I'd continue the fun by expanding the capabilities of Ben's 8-bit CPU even further. That said, you'll need to have done the work in the previous post to be able to do this. You can get a sense for what we'll do in this Imgur gallery.
In this tutorial, we'll balance software and hardware improvements to make this a pretty capable machine:

Parts List

To only update the hardware, you'll need:
If you want to update the toolchain, you'll need:
  1. Arduino Mega 2560 (Amazon) to create the programmer.
  2. Ribbon Jumper Cables (Amazon) to connect the Arduino to the breadboard.
  3. TL866 II Plus EEPROM Programmer (Amazon) to program the ROM.
Bonus Clock Improvement: One additional thing I did is replace the 74LS04 inverter in Ben's clock circuit with a 74LS14 inverting Schmitt trigger (datasheet, Jameco). The pinouts are identical! Just drop it in, wire the existing lines, and then run the clock output through it twice (since it's inverting) to get a squeaky clean clock signal. Useful if you want to go even faster with the CPU.

Step 1: Program with an Arduino and Assembler (Image 1, Image 2)

There's a certain delight in the physical programming of a computer with switches. This is how Bill Gates and Paul Allen famously programmed the Altair 8800 and started Microsoft. But at some point, the hardware becomes limited by how effectively you can input the software. After upgrading the RAM, I quickly felt constrained by how long it took to program everything.
You can continue to program the computer physically if you want and even after upgrading that option is still available, so this step is optional. There's probably many ways to approach the programming, but this way felt simple and in the spirit of the build. We'll use an Arduino Mega 2560, like the one in Ben's 6502 build, to program the RAM. We'll start with a homemade assembler then switch to something more robust.
Preparing the Physical Interface
The first thing to do is prepare the CPU to be programmed by the Arduino. We already did the hard work on this in the RAM upgrade tutorial by using the bus to write to the RAM and disconnecting the control ROM while in program mode. Now we just need to route the appropriate lines to a convenient spot on the board to plug the Arduino into.
  1. This is optional, but I rewired all the DIP switches to have ground on one side, rather than alternating sides like Ben's build. This just makes it easier to route wires.
  2. Wire the 8 address lines from the DIP switch, connecting the side opposite to ground (the one going to the chips) to a convenient point on the board. I put them on the far left, next to the address LEDs and above the write button circuit.
  3. Wire the 8 data lines from the DIP switch, connecting the side opposite to ground (the one going to the chips) directly below the address lines. Make sure they're separated by the gutter so they're not connected.
  4. Wire a line from the write button to your input area. You want to connect the side of the button that's not connected to ground (the one going to the chip).
So now you have one convenient spot with 8 address lines, 8 data lines, and a write line. If you want to get fancy, you can wire them into some kind of connector, but I found that ribbon jumper cables work nicely and keep things tidy.
The way we'll program the RAM is to enter program mode and set all the DIP switches to the high position (e.g., 11111111). Since the switches are upside-down, this means they'll all be disconnected and not driving to ground. The address and write lines will simply be floating and the data lines will be weakly pulled up by 1k resistors. Either way, the Arduino can now drive the signals going into the chips using its outputs.
Creating the Arduino Programmer
Now that we can interface with an Arduino, we need to write some software. If you follow Ben's 6502 video, you'll have all the knowledge you need to get this working. If you want some hints and code, see below (source code):
  1. Create arrays for your data and address lines. For example: const char ADDRESS_LINES[] = {39, 41, 43, 45, 47, 49, 51, 53};. Create your write line with #define RAM_WRITE 3.
  2. Create functions to enable and disable your address and data lines. You want to enable them before writing. Make sure to disable them afterward so that you can still manually program using DIP switches without disconnecting the Arduino. The code looks like this (just change INPUT to OUTPUT accordingly): for(int n = 0; n < 8; n += 1) { pinMode(ADDRESS_LINES[n], OUTPUT); }
  3. Create a function to write to an address. It'll look like void writeData(byte writeAddress, byte writeData) and basically use two loops, one for address and one for data, followed by toggling the write.
  4. Create a char array that contains your program and data. You can use #define to create opcodes like #define LDA 0x01.
  5. In your main function, loop through the program array and send it through writeData.
With this setup, you can now load multi-line programs in a fraction of a second! This can really come in handy with debugging by stress testing your CPU with software. Make sure to test your setup with existing programs you know run reliably. Now that you have your basic setup working, you can add 8 additional lines to read the bus and expand the program to let you read memory locations or even monitor the running of your CPU.
Making an Assembler
The above will serve us well but it's missing a key feature: labels. Labels are invaluable in assembly because they're so versatile. Jumps, subroutines, variables all use labels. The problem is that labels require parsing. Parsing is a fun project on the road to a compiler but not something I wanted to delve into right now--if you're interested, you can learn about Flex and Bison. Instead, I found a custom assembler that lets you define your CPU's instruction set and it'll do everything else for you. Let's get it setup:
  1. If you're on Windows, you can use the pre-built binaries. Otherwise, you'll need to install Rust and compile via cargo build.
  2. Create a file called 8bit.cpu and define your CPU instructions (source code). For example, LDA would be lda {address} -> 0x01 @ address[7:0]. What's cool is you can also now create the instruction's immediate variant instead of having to call it LDI: lda #{value} -> 0x05 @ value[7:0].
  3. You can now write assembly by adding #include "8bit.cpu" to the top of your code. There's a lot of neat features so make sure to read the documentation!
  4. Once you've written some assembly, you can generate the machine code using ./customasm yourprogram.s -f hexc -p. This prints out a char array just like our Arduino program used!
  5. Copy the char array into your Arduino program and send it to your CPU.
At this stage, you can start creating some pretty complex programs with ease. I would definitely play around with writing some larger programs. I actually found a bug in my hardware that was hidden for a while because my programs were never very complex!

Step 2: Expand the Control Lines (Image)

Before we can expand the CPU any further, we have to address the fact we're running out of control lines. An easy way to do this is to add a 3rd 28C16 ROM and be on your way. If you want something a little more involved but satisfying, read on.
Right now the control lines are one hot encoded. This means that if you have 4 lines, you can encode 4 states. But we know that a 4-bit binary number can encode 16 states. We'll use this principle via 74LS138 decoders, just like Ben used for the step counter.
Choosing the Control Line Combinations
Everything comes with trade-offs. In the case of combining control lines, it means the two control lines we choose to combine can never be activated at the same time. We can ensure this by encoding all the inputs together in the first 74LS138 and all the outputs together in a second 74LS138. We'll keep the remaining control lines directly connected.
Rewiring the Control Lines
If your build is anything like mine, the control lines are a bit of a mess. You'll need to be careful when rewiring to ensure it all comes back together correctly. Let's get to it:
  1. Place the two 74LS138 decoders on the far right side of the breadboard with the ROMs. Connect them to power and ground.
  2. You'll likely run out of inverters, so place a 74LS04 on the breadboard above your decoders. Connect it to power and ground.
  3. Carefully take your inputs (MI, RI, II, AI, BI, J) and wire them to the outputs of the left 74LS138. Do not wire anything to O0 because that's activated by 000 which won't work for us!
  4. Carefully take your outputs (RO, CO, AO, EO) and wire them to the outputs of the right 74LS138. Remember, do not wire anything to O0!
  5. Now, the 74LS138 outputs are active low, but the ROM outputs were active high. This means you need to swap the wiring on all your existing 74LS04 inverters for the LEDs and control lines to work. Make sure you track which control lines are supposed to be active high vs. active low!
  6. Wire E3 to power and E2 to ground. Connect the E1 on both 138s together, then connect it to the same line as OE on your ROMs. This will ensure that the outputs are disabled when you're in program mode. You can actually take off the 1k pull-up resistors from the previous tutorial at this stage, because the 138s actively drive the lines going to the 74LS04 inverters rather than floating like the ROMs.
At this point, you really need to ensure that the massive rewiring job was successful. Connect 3 jumper wires to A0-A2 and test all the combinations manually. Make sure the correct LED lights up and check with a multimeteoscilloscope that you're getting the right signal at each chip. Catching mistakes at this point will save you a lot of headaches! Now that everything is working, let's finish up:
  1. Connect A0-A2 of the left 74LS138 to the left ROM's A0-A2.
  2. Connect A0-A2 of the right 74LS138 to the right ROM's A0-A2.
  3. Distribute the rest of the control signals across the two ROMs.
Changing the ROM Code
This part is easy. We just need to update all of our #define with the new addresses and program the ROMs again. For clarity that we're not using one-hot encoding anymore, I recommend using hex instead of binary. So instead of #define MI 0b0000000100000000, we can use #define MI 0x0100, #define RI 0x0200, and so on.
Expanding the control lines required physically rewiring a lot of critical stuff, so small mistakes can creep up and make mysterious errors down the road. Write a program that activates each control line at least once and make sure it works properly! With your assembler and Arduino programmer, this should be trivial.
Bonus: Adding B Register Output
With the additional control lines, don't forget you can now add a BO signal easily which lets you fully use the B register.

Step 3: Add a Stack (Image 1, Image 2)

Adding a stack significantly expands the capability of the CPU. It enables subroutines, recursion, and handling interrupts (with some additional logic). We'll create our stack with an 8-bit stack pointer hard-coded from $0100 to $01FF, just like the 6502.
Wiring up the Stack Pointer
A stack pointer is conceptually similar to a program counter. It stores an address, you can read it and write to it, and it increments. The only difference between a stack pointer and a program counter is that the stack pointer must also decrement. To create our stack pointer, we'll use two 74LS193 4-bit up/down binary counters:
  1. Place a 74LS00 NAND gate, 74LS245 transceiver, and two 74LS193 counters in a row next to your output register. Wire up power and ground.
  2. Wire the the Carry output of the right 193 to the Count Up input of the left 193. Do the same for the Borrow output and Count Down input.
  3. Connect the Clear input between the two 193s and with an active high reset line. The B register has one you can use on its 74LS173s.
  4. Connect the Load input between the two 193s and to a new active low control line called SI on your 74LS138 decoder.
  5. Connect the QA-QD outputs of the lower counter to A8-A5 and the upper counter to A4-A1. Pay special attention because the output are in a weird order (BACD) and you want to make sure the lower A is connected to A8 and the upper A is connected to A4.
  6. Connect the A-D inputs of the lower counter to B8-B5 and the upper counter to B4-B1. Again, the inputs are in a weird order and on both sides of the chip so pay special attention.
  7. Connect the B1-B8 outputs of the 74LS245 transceiver to the bus.
  8. On the 74LS245 transceiver, connect DIR to power (high) and connect OE to a new active low control line called SO on your 74LS138 decoder.
  9. Add 8 LEDs and resistors to the lower part of the 74LS245 transceiver (A1-A8) so you can see what's going on with the stack pointer.
Enabling Increment & Decrement
We've now connected everything but the Count Up and Count Down inputs. The way the 74LS193 works is that if nothing is counting, both inputs are high. If you want to increment, you keep Count Down high and pulse Count Up. To decrement, you do the opposite. We'll use a 74LS00 NAND gate for this:
  1. Take the clock from the 74LS08 AND gate and make it an input into two different NAND gates on the 74LS00.
  2. Take the output from one NAND gate and wire it to the Count Up input on the lower 74LS193 counter. Take the other output and wire it to the Count Down input.
  3. Wire up a new active high control line called SP from your ROM to the NAND gate going into Count Up.
  4. Wire up a new active high control line called SM from your ROM to the NAND gate going into Count Down.
At this point, everything should be working. Your counter should be able to reset, input a value, output a value, and increment/decrement. But the issue is it'll be writing to $0000 to $00FF in the RAM! Let's fix that.
Accessing Higher Memory Addresses
We need the stack to be in a different place in memory than our regular program. The problem is, we only have an 8-bit bus, so how do we tell the RAM we want a higher address? We'll use a special control line to do this:
  1. Wire up an active high line called SA from the 28C16 ROM to A8 on the Cypress CY7C199 RAM.
  2. Add an LED and resistor so you can see when the stack is active.
That's it! Now, whenever we need the stack we can use a combination of the control line and stack pointer to access $0100 to $01FF.
Updating the Instruction Set
All that's left now is to create some instructions that utilize the stack. We'll need to settle some conventions before we begin:
If you want to add a little personal flair to your design, you can change the convention fairly easily. Let's implement push and pop (source code):
  1. Define all your new control lines, such as #define SI 0x0700 and #define SO 0x0005.
  2. Create two new instructions: PSH (1011) and POP (1100).
  3. PSH starts the same as any other for the first two steps: MI|CO and RO|II|CE. The next step is to put the contents of the stack pointer into the address register via MI|SO|SA. Recall that SA is the special control line that tells the memory to access the $01XX bank rather than $00XX.
  4. We then take the contents of AO and write it into the RAM. We can also increment the stack pointer at this stage. All of this is done via: AO|RI|SP|SA, followed by TR.
  5. POP is pretty similar. Start off with MI|CO and RO|II|CE. We then need to take a cycle and decrement the stack pointer with SM. Like with PSH, we then set the address register with MI|SO|SA.
  6. We now just need to output the RAM into our A register with RO|AI|SA and then end the instruction with TR.
  7. Updating the assembler is easy since neither instruction has operands. For example, push is just psh -> 0x0B.
And that's it! Write some programs that take advantage of your new 256 byte stack to make sure everything works as expected.

Step 4: Add Subroutine Instructions (Image)

The last step to complete our stack is to add subroutine instructions. This allows us to write complex programs and paves the way for things like interrupt handling.
Subroutines are like a blend of push/pop instructions and a jump. Basically, when you want to call a subroutine, you save your spot in the program by pushing the program counter onto the stack, then jumping to the subroutine's location in memory. When you're done with the subroutine, you simply pop the program counter value from the stack and jump back into it.
We'll follow 6502 conventions and only save and restore the program counter for subroutines. Other CPUs may choose to save more state, but it's generally left up to the programmer to ensure they're not wiping out states in their subroutines (e.g., push the A register at the start of your subroutine if you're messing with it and restore it before you leave).
Adding an Extra Opcode Line
I've started running low on opcodes at this point. Luckily, we still have two free address lines we can use. To enable 5-bit opcodes, simply wire up the 4Q output of your upper 74LS173 register to A7 of your 28C16 ROM (this assumes your opcodes are at A3-A6).
Updating the ROM Writer
At this point, you simply need to update the Arduino writer to support 32 instructions vs. the current 16. So, for example, UCODE_TEMPLATE[16][8] becomes UCODE_TEMPLATE[32][8] and you fill in the 16 new array elements with nop. The problem is that the Arduino only has so much memory and with the way Ben's code is written to support conditional jumps, it starts to get tight.
I bet the code can be re-written to handle this, but I had a TL866II Plus EEPROM programmer handy from the 6502 build and I felt it would be easier to start using that instead. Converting to a regular C program is really simple (source code):
  1. Copy all the #define, global const arrays (don't forget to expand them from 16 to 32), and void initUCode(). Add #include and #include to the top.
  2. In your traditional int main (void) C function, after initializing with initUCode(), make two arrays: char ucode_upper[2048] and char ucode_lower[2048].
  3. Take your existing loop code that loops through all addresses: for (int address = 0; address < 2048; address++).
  4. Modify instruction to be 5-bit with int instruction = (address & 0b00011111000) >> 3;.
  5. When writing, just write to the arrays like so: ucode_lower[address] = ucode[flags][instruction][step]; and ucode_upper[address] = ucode[flags][instruction][step] >> 8;.
  6. Open a new file with FILE *f = fopen("rom_upper.hex", "wb");, write to it with fwrite(ucode_upper, sizeof(char), sizeof(ucode_upper), f); and close it with fclose(f);. Repeat this with the lower ROM too.
  7. Compile your code using gcc (you can use any C compiler), like so: gcc -Wall makerom.c -o makerom.
Running your program will spit out two binary files with the full contents of each ROM. Writing the file via the TL866II Plus requires minipro and the following command: minipro -p CAT28C16A -w rom_upper.hex.
Adding Subroutine Instructions
At this point, I cleaned up my instruction set layout a bit. I made psh and pop 1000 and 1001, respectively. I then created two new instructions: jsr and rts. These allow us to jump to a subroutine and returns from a subroutine. They're relatively simple:
  1. For jsr, the first three steps are the same as psh: MI|CO, RO|II|CE, MI|SO|SA.
  2. On the next step, instead of AO we use CO to save the program counter to the stack: CO|RI|SP|SA.
  3. We then essentially read the 2nd byte to do a jump and terminate: MI|CO, RO|J.
  4. For rts, the first four steps are the same as pop: MI|CO, RO|II|CE, SM, MI|SO|SA.
  5. On the next step, instead of AI we use J to load the program counter with the contents in stack: RO|J|SA.
  6. We're not done! If we just left this as-is, we'd jump to the 2nd byte of jsr which is not an opcode, but a memory address. All hell would break loose! We need to add a CE step to increment the program counter and then terminate.
Once you update the ROM, you should have fully functioning subroutines with 5-bit opcodes. One great way to test them is to create a recursive program to calculate something--just don't go too deep or you'll end up with a stack overflow!


And that's it! Another successful upgrade of your 8-bit CPU. You now have a very capable machine and toolchain. At this point I would have a bunch of fun with the software aspects. In terms of hardware, there's a number of ways to go from here:
  1. Interrupts. Interrupts are just special subroutines triggered by an external line. You can make one similar to how Ben did conditional jumps. The only added complexity is the need to load/save the flags register since an interrupt can happen at any time and you don't want to destroy the state. Given this would take more than 8 steps, you'd also need to add another line for the step counter (see below).
  2. ROM expansion. At this point, address lines on the ROM are getting tight which limits any expansion possibilities. With the new approach to ROM programming, it's trivial to switch out the 28C16 for the 28C256 that Ben uses in the 6502. These give you 4 additional address lines for flags/interrupts, opcodes, and steps.
  3. LCD output. At this point, adding a 16x2 character LCD like Ben uses in the 6502 is very possible.
  4. Segment/bank register. It's essentially a 2nd memory address register that lets you access 256-byte segments/banks of RAM using bank switching. This lets you take full advantage of the 32K of RAM in the Cypress chip.
  5. Fast increment instructions. Add these to registers by replacing 74LS173s with 74LS193s, allowing you to more quickly increment without going through the ALU. This is used to speed up loops and array operations.
submitted by MironV to beneater [link] [comments]

Review of ExpertOption. Binary options signals Expert ... Binary Options Trading Signals - YouTube Binary Options Strategy & Trading Systems Full Explanation - Trading binary options live tutorial ... How Forex Spot Trading A Simple Guide Binary Options ... [Für Anfänger entwickelt] Binäre Optionen Signale mit Wahnsinns-Gewinnquote (über 90%)!!!

AllFXBrokers is a Forex and Binary Options Brokers Directory, that helps traders find brokers based on a unique categorization system. A detailed information portal is also provided. ADVERTISEMENT  Top Brokers. ECN/STP (DEPOSIT BONUS, FAST WITHDRAWAL) Review & Rating Open Live Account. Your capital is at risk . ECN/STP (TRADE FOREX WITH LOWER SPREADS) Review & Rating Open Live Account. Your ... Good account and good broker. The deposit is small, profits are nice. Expiration is the best for me. Spot Option is the best platform for binary options trading. Money video auto opzioni binarie democracy meaning binary 900 v2.0 dlg glider.ritrova nei strategie opzioni binarie minuti come cambiare lingua opzioni internet.traden man canadian binary options segnali ultra binary auto trader scam binarie eq binary options. Vincente opzioni binarie, her ultra binary image:.strategie opzioni binarie.votato. China has released harder principles on the exchanging stock catalog futures in addition to forex trading imitative as it searches for help constant in jittery areas as their weak spot has raised be concerned about the health of second-largest financial system. As they are going through sluggish monetary development and as well as losses in share market, Beijing has prioritize near-term ... Cme Single Stock Options Cme Group Inc Cme Option Chain. Galerie Photo Du Model Club De La Meuse Tabora 22 Decembre 2012 . Sandalii Alla Pugachova Zhenskaya Obuv Obuv Katalog Tovarov. Galerie Photo Du Model Club De La Meuse Tabora 8 Decembre 2012. Share: Read More. Monday, August 24, 2020. Forex Handel In Australien. August 24, 2020 No comments: Roboter Check Lanticahostaria Eu. Binare ... Search the world's information, including webpages, images, videos and more. Google has many special features to help you find exactly what you're looking for. Binary Options Indicators; Experts Advisors; No Deposit Bonuses; Home. Back . Forex Indicators. Only the best forex indicators worthy of attention and analysis are published in this category. All forex indicators can download free. Most of them are not repainted and are really able to facilitate the trader’s everyday life. 26. 25242. Forex Millennium - new forex indicator with effective ... Sapete a.legendary binary options trading platform.learn why we are on of the piattaforma iq option permette ai suoi trader di concludere gli affari a partire da.shot del conto skrill con i prelievi da iq option europe limited.scopriamo le truffe inaudite di iq option al interno della nostra option, trading di opzioni binarie. Account. Come posso.ho pronti.expertoption ... reliable signals of future market behavior. This guide is intended as an introduction to some of these patterns, which helptraders make sense of market conditions and recognize advantageous times to enter trades. The ability to read candlesticks allows the price action trader to become a meta-strategist, taking into account the behaviors of other traders and large-scale market-movers. In other ... Are they spot on or just another con? Read our unbiased John Anthony Signals review to find out more about this binary options trading software system. What is John Anthony Signals? John Anthony Signals is a fully automated trading system that promises to send its members up to 17 reliable trades a day. This is nothing special, as most signal providers provide at least that many signals a day ...

[index] [2292] [13430] [9367] [5732] [1039] [13552] [4560] [1095] [26297] [18310]

Review of ExpertOption. Binary options signals Expert ...

ExpertOption - Expert Option Review of ExpertOption. ... Confirm your spot here ... Binary Options Doctor Binary Options Strategy & Trading Systems 3,094 views. 11:35. 2 Minutes Strategy Binary Options 2020 (IQ Options) - Duration: 17:06. D - Trading ... Take The Stress Out of Trading - Get Into Binary Options Today! If you've never heard of Binary Options before, you probably trade Forex, Stocks, Commodities... Trusted spots blog To register a free account on desktop or laptop, click here To register a f... Binäre Optionen Erklärung 😂 Online Trading 👉 Bestes Trendfolge Forex System 👈 Iq Option Broker💋 - Duration: 18:41. 27,054 views 18:41 das ergebnis der 95% in 60 sekunden - meine platte ---free binary options trading signals how to make money from binary option mit binären optionen geld verdienen binary options live signals ... CLICK HERE FOR MORE INFO: And start earning in the Forex Market Now! In our expanding international business setting, there are bu...